specification model dc voltage rated current current range rated power output voltage adj. range line regulation load regulation setup, rise time hold up time (typ.) voltage range note.5 frequency range efficiency (typ.) input function inrush current (typ.) leakage current over temperature working temp. current sharing(cs) note.7 output voltage trim note.6 dc ok signal remote on/off control note.6 auxiliary power(aux) working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing overload over voltage ac current (typ.) 300ms, 50ms at full load 16ms/230vac 16ms/115vac at full load 90 ~ 264vac 127 ~ 370vdc 47 ~ 63hz 12a/115vac 6a/230vac 25a/115vac 40a/230vac <2.0ma / 240vac 105 ~ 125% rated output power protection type : constant current limiting, recovers automatically after fault condition is removed 13.8 ~ 16.8v 17 ~ 20.5v 27.6 ~ 32.4v 31 ~ 36.5v 56.6 ~ 66.2v protection type : shut down o/p voltage, re-power on to recover 85 5 (tsw2 ) detect on heatsink of o/p diode; 7 5 5 (tsw1 ) detect on heatsink of power transistor protection type : shut down o/p voltage, recovers automatically after t emperature goes down -20 ~ +60 (refer to output load derating curve) power on : short between on/off(pin6) & -s(pin2) on cn50 power off : open betwe en on/off(pin6) & -s(pin2) on cn50 the ttl signal out, psu turn on = 0 ~ 1v ; psu turn off = 3.3 ~ 5.6v adjustment of output voltage is possible between 40 ~ 110% of rated output please refer to function manual 5v @ 0.5a (+5%, -8%) 20 ~ 90% rh non-condensing -40 ~ +85 , 10 ~ 95% rh 0.02%/ (0 ~ 50 ) 10 ~ 500hz, 2g 10min./1cycle, 60min. each along x, y, z axes 116.75k hrs min. mil-hdbk-217f (25 ) 295*127*41mm (l*w*h) 1.95kg; 6pcs/12.7kg/0.99cuft 83% 85% 88% 88% 90% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 1.0% 1.0% 1.0% 1.0% 1.0% 150mvp-p 10 ~ 13.5v 150mvp-p 13.5 ~ 16.5v 150mvp-p 20 ~ 26.4v 150mvp-p 24 ~ 30v 150mvp-p 43 ~ 55v 12v 60a 0 ~ 60a 720w 15v 50a 0 ~ 50a 750w 24v 40a 0 ~ 40a 960w 27v 37a 0 ~ 37a 999w 48v 21a 0 ~ 21a 1008w rsp-1000-12 rsp-1000-15 rsp-1000-24 rsp-1000-27 rsp-100 0-48 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. the power supply is considered a component which will be installed into a fi nal equipment. the final equipment must be re-confirmed that it still me ets emc directives. 5. derating may be needed under low input voltages. please check the derati ng curve for more details. 6. the power supply unit will have no output if the shorting connector is not ass embled. it contains two shorting wires: one is from on/off(pin6) to -s(p in2) and the other is from vco(pin8) to vca(pin10). please refter to function ma nual for details. 7. in parallel connection, maybe only one unit operate if the total output l oad is less than 5% of rated load condition. 8. please consult mean well for applications of more units connecting in pa rallel. for guidance on how to perform these emc tests, please refer to ?emi testing of c omponent power supplies.? (as available on http://www.meanwell.com) power factor (typ.) 0.95/230vac 0.98/115vac at full load safety standards harmonic current ems immunity ul60950-1, tuv en60950-1 approved compliance to en55022 (cispr22) compliance to en61000-3-2,-3 compliance to en61000-4-2,3,4,5,6,8,11; env50204, en55024, e n61000-6-2, en61204-3, heavy industry level, criteria a 1000w single output power supply r s p - 1 0 0 0 s e r i e s ripple & noise (max.) note.2 voltage tolerance note.3 emi conduction & radiation withstand voltage isolation resistance i/p-o/p:3kvac i/p-fg:1.5kvac o/p-fg:0.5kvac i/p-o/p, i/p-fg, o/p-fg:100m ohms / 500vdc / 25 / 70% rh environment safety & emc (note 4) protection universal ac input / full rangeac input active surge current limiting built-in 5v/0.5a auxiliary power built-in active pfc function, pf>0.95 protections: short circuit / overload / over voltage / over temperature output voltage can be trimmed between 40 ~ 110% of the rated output voltage forced air cooling by built-in dc fan active current sharing up to 4000w(3+1) dc ok signal built-in remote on-off control built-in remote sense function 3 years warranty (note.8) high power density 10.7w/inch1u low profile 41mm 3 features : .. file name:rsp-1000-spec 2011-02-17
mechanical specification derating curve static characteristics case no. 952b unit:mm load (%) input voltage (vac) 60hz 90 95 100 115 264 90 100 80 70 60 50 40 block diagram ambient temperature ( ) load (%) 20 40 60 80 100 -20 0 10 20 30 40 50 60 70 ta=25 pfc fosc : 110khz pwm fosc : 90khz ac input terminal pin no. assignment pin no. 13 2 assignment fg ac/l ac/n 1 11 tb1 32 1 7 +v -v 20.5 air flow direction 41 127 18.5 3-m4 l=4 90 10 6 277.7 25.4 7.8 21 34.5 59 295 277.7 25.4 7.8 6 20.5 control pi (cn50) : n no. assignment hrs df11-12dp-2ds or equivalent pin no. pin no. pin no. 9 5 1 10 6 11,12 78 23 4 assignment assignment assignment vci dc-ok +s vca gnd -s cs on/off vco g-aux 5v-aux mating housing hrs df11-12ds or equivalent terminal hrs df11-**sc or equivalent cn50 2 12 svr51 3-m4 l=6 3-m4 l=6 & pfc filter & rectifiers aux power(5v/0.5a) pfc control o.l.p. aux gnd share current current v_trim dc ok share o.v.p. on/off rectifiers control on/off fan limiting active current inrush control i/p -v +v rectifiers & filter switching power rectifiers filter emi pwm -s +s circuit detection power aux 1000w single output power supply r s p - 1 0 0 0 s e r i e s file name:rsp-1000-spec 2011-02-17 (horizontal)
tb1 fig 1.1 load - + svr51 cn50 1 11 2 12 -v +v the power supply unit will have no output if the shorting connector (access ory comes along with the psu) is not assembled. it contains two shorting wires : one is from on/off (pin6) to -s (pin2) and the other is from vco ( pin8) to vca (pin10). +s 1 -s 2 auxg aux dc_ok on/off cs cn50 (shorting connector) vco vci vca gnd 11 gnd 12 1000w single output power supply r s p - 1 0 0 0 s e r i e s function description of cn50 function manual 1."remote on/off" and "output voltage trim" functions are not used. pin no. function description 14 5 7 8 10 11,12 23 6 9 +s 5v-aux dc_ok cs vco vca gnd -s g-aux on/off vci auxiliary voltage output, 4.6~5.25v, referenced to pin 3(g-aux). t he maximum load current is 0.5a. this output has the built-in oring diodes and is not controlled by the "remote on/off control". open collector signal, referenced to pin11,12(gnd). low when psu turn s on. the maximum sink current is 10ma and the maximum external voltage is 5.6v. current sharing signal. when units are connected in parallel, the cs pins o f the units should be connected to allow current balance between units. short connecting between vco (pin8) and vca (pin10) if output voltage tri m function is not used. connect to external resistor (1/8w) for output voltage triming. outpu t voltage can be trimmed between 40 ~ 110% of the rated output voltage. please refer to function manual for details. these pins connect to the negative terminal (-v). return for dc_ok signal o utput. turns the output on and off by electrical or dry contact between pin 6 ( on/off) an d pin 2 (-s). short: power on, open: power off. connect to external dc voltage source for output voltage triming, refer enced to pin 2 (-s). output voltage can be trimmed between 40 ~ 110% of the rated output voltage. negative sensing. the -s signal should be connected to the negative term inal of the load. the -s and +s leads should be twisted in pair to minimize noise pick-up effect. the maximum line drop compensation i s 0.5v. positive sensing. the +s signal should be connected to the positive term inal of the load. the +s and -s leads should be twisted in pair to minimize noise pick-up effect. the maximum line drop compensation i s 0.5v. auxiliary voltage output ground. the signal return is isolated from th e output terminals (+v & -v). file name:rsp-1000-spec 2011-02-17
1000w single output power supply r s p - 1 0 0 0 s e r i e s the remote sensing compensates voltage drop on the load wiring up to 0.5v. fig 4.1 -v +v tb1 cn50 svr51 - + load -s (pin2) sense lines should be twisted in pairs +s (pin1) 4.remote sense fig 3.1 cn50 1 11 2 12 1 11 2 12 -v +v tb1 svr51 3.dc_ok signal "dc_ok" is an open collector signal. it indicates the output status of the psu. it can operate in two ways : one is sinking current from external ttl signal ; the other is sending out a ttl voltage signal. the maximum sink current is 10ma and the maximum external voltage is 5.6v. 3-1 sink current : 3-2 ttl voltage signal : between dc- ok(pin5) and gnd(pin11&12) between on/off(pin6) and -s(pin2) 0 ~ 1v sw on (short) 3.3 ~ 5.6v sw off (open) output status output status on on off off 2.remote on/off tb1 fig 2.1 load - + svr51 cn50 1 11 2 12 sw -v +v the psu can be turned on/off by using the "remote on/off" function +s +s +s 11 1 -s -s -s 2 22 auxg auxg auxg aux aux aux dc_okdc_ok dc_ok on/offon/off on/off cs cs cs cn50 cn50 cn50 vco vco vco vci vci vci vca vca vca gnd gnd gnd 11 11 11 gnd gnd gnd 12 12 12 file name:rsp-1000-spec 2011-02-17
(1)using external voltage source between "vci"(pin9) and "-s"(pin2) that is shown in fig5.1 output voltage of rsp-1000 can be trimmed between 40% ~ 110% of its rated value by the following methods : (2)connecting a resistor externally that in shown in fig 5.2 & fig 5.3 (a) o/p voltage goes down (b)o/p voltage goes up external voltage (vdc) external resistor ( ) external resistor ( ) 1 390 2 560 open 3 820 4 1k2 18k 5 2k2 6 4k7 7k5 open vci(referenced to -s) r1, 1/8w(typ.) r2, 1/8w(typ.) 100 80 110 120 90 100 vout vout vout ovp 120%(typ.) ovp 120%(typ.) non-linear 80 70 60 60 non-linear non-linear 105 40 50 20 40 100 tb1 svr51 r1 r2 -v +v +s 11 +s -s 22 -s auxg auxg aux aux dc_ok on/off dc_ok on/off cs cs cn50 cn50 vco vco vci vci vca vca gnd 11 11 gnd gnd 12 12 gnd 5.output voltage trim output voltage (%) output voltage (%) output voltage (%) cn50 1 11 2 12 fig 5.1 fig 5.2 fig 5.3 external voltage +s 1 -s 2 auxg aux dc_ok on/off cs cn50 vco vci vca gnd 11 gnd 12 1000w single output power supply r s p - 1 0 0 0 s e r i e s file name:rsp-1000-spec 2011-02-17
6.current sharing with remote sensing rsp-1000 has the built-in active current sharing function and can be conn ected in parallel to provide higher output power : (1)parallel operation is available by connecting the units shown as bel ow. (+s,-s and cs are connected mutually in parallel). (2)difference of output voltages among parallel units should be less th an 2%. (3)the total output current must not exceed the value determined by the fol lowing equation. (4)in parallel operation 4 units is the maximum, please consult the manuf acturer for applications of more connecting in parallel. (5)the power supplies should be paralleled using short and large diamet er wiring and then connected to the load. (output current at parallel operation)=(rated current per unit) (n umber of unit) 0.9 note : in parallel connection, maybe only one unit (master) operate if the to tal output load is less than 5% of rated load condition. the other psus (slaves) may go into standby mode and their output leds will not t urn on. +s +s +s +s -s -s -s -s auxg auxg auxg auxg aux aux aux aux dc_ok dc_ok dc_ok dc_ok on/off on/off on/off on/off cs cs cs cs vco vco vco vco vci vci vci vci vca vca vca vca gnd gnd gnd gnd gnd gnd gnd gnd psu psu psu psu -v sense lines should be twisted in pairs svr51 svr51 svr51 svr51 +v load cn50 cn50 cn50 cn50 tb1 tb1 tb1 tb1 +v +v +v +v -v -v -v -v 1 11 2 12 1 11 2 12 1 11 2 12 1 11 2 12 1 1 1 1 11 11 11 11 cn50 cn50 cn50 cn50 fig 6.1 cs(pin7) +s(pin1) -s(pin2) 2 2 2 2 12 12 12 12 1000w single output power supply r s p - 1 0 0 0 s e r i e s file name:rsp-1000-spec 2011-02-17
|
